Linux Thunderbolt 3 Dock (40AC): Funktioniert nur bei jedem 2. Suspend

[Matze88]

Hallo zusammen,

ich hab mir zu meinem T480 vor ein paar Monaten ne gebrauchte 40AC Dock (Thunderbolt 3 Dock, aber die "alte") günstig geschossen. Leider scheint mir das Thunderbolt-Zeugs etwas unausgereift, nun ich habe folgendes Problem:

Nach einem Suspend und wiederaufwachen funktionieren sämtliche USB-Geräte nicht, die Bildschirme gehen an. Ich muss dann das Notebook nochmal suspenden (Power-Taste drücken), ein paar Sekunden warten, aufwecken; dann gehts.
Das ist zuverlässig so reproduzierbar, sprich es passiert jedes mal nach nem Suspend und geht dann immer mit nochmal-suspenden wieder.

Firmware vom Dock hab ich gerade unter Windows geupdated, aber das hat nichts geändert (Datenpunkt: mit fwupdmgr konnte ich unter Linux das Dock nicht updaten - habs dann mit nem per Rufus erstellen Windows-Live-Stick gemacht).
Archlinux, 6.3.3-arch1-1, ich hab auch tlp laufen, sehe da aber nichts, was mit dem Dock interagieren könnte...
Das Problem besteht seit ich das Dock hab, also keine Veränderung mit Kernel Updates etc. die letzten Monate.

dmesg mit Fehler:

[  142.082602] ACPI: PM: Low-level resume complete
[  142.082648] ACPI: EC: EC started
[  142.082649] ACPI: PM: Restoring platform NVS memory
[  142.083719] Enabling non-boot CPUs ...
[  142.083822] x86: Booting SMP configuration:
[  142.083822] smpboot: Booting Node 0 Processor 1 APIC 0x2
[  142.085678] CPU1 is up
[  142.085769] smpboot: Booting Node 0 Processor 2 APIC 0x4
[  142.087629] CPU2 is up
[  142.087744] smpboot: Booting Node 0 Processor 3 APIC 0x6
[  142.089622] CPU3 is up
[  142.089740] smpboot: Booting Node 0 Processor 4 APIC 0x1
[  142.090565] CPU4 is up
[  142.090687] smpboot: Booting Node 0 Processor 5 APIC 0x3
[  142.091474] CPU5 is up
[  142.091619] smpboot: Booting Node 0 Processor 6 APIC 0x5
[  142.092456] CPU6 is up
[  142.092561] smpboot: Booting Node 0 Processor 7 APIC 0x7
[  142.093458] CPU7 is up
[  142.096331] ACPI: PM: Waking up from system sleep state S3
[  142.514261] ACPI: EC: interrupt unblocked
[  142.514764] pcieport 0000:00:1c.6: Intel SPT PCH root port ACS workaround enabled
[  142.514788] pcieport 0000:00:1d.2: Intel SPT PCH root port ACS workaround enabled
[  142.514790] pcieport 0000:00:1d.0: Intel SPT PCH root port ACS workaround enabled
[  142.532666] pcieport 0000:07:00.0: Unable to change power state from unknown to D0, device inaccessible
[  142.535103] pcieport 0000:08:01.0: Unable to change power state from D3hot to D0, device inaccessible
[  142.535105] pcieport 0000:08:00.0: Unable to change power state from D3hot to D0, device inaccessible
[  142.535140] pcieport 0000:08:04.0: Unable to change power state from unknown to D0, device inaccessible
[  142.535142] pcieport 0000:08:02.0: Unable to change power state from D3hot to D0, device inaccessible
[  142.535145] pcieport 0000:08:03.0: Unable to change power state from D3hot to D0, device inaccessible
[  142.545415] xhci_hcd 0000:09:00.0: Unable to change power state from D3hot to D0, device inaccessible
[  142.545474] xhci_hcd 0000:0b:00.0: Unable to change power state from D3hot to D0, device inaccessible
[  142.623148] pcieport 0000:00:1c.0: Intel SPT PCH root port ACS workaround enabled
[  142.755390] vfio-pci 0000:01:00.0: Enabling HDA controller
[  142.757006] ACPI: EC: event unblocked
[  142.759236] xhci_hcd 0000:09:00.0: Unable to change power state from D3cold to D0, device inaccessible
[  142.759237] xhci_hcd 0000:0b:00.0: Unable to change power state from D3cold to D0, device inaccessible
[  142.759245] xhci_hcd 0000:0b:00.0: Controller not ready at resume -19
[  142.759246] xhci_hcd 0000:09:00.0: Controller not ready at resume -19
[  142.759246] xhci_hcd 0000:0b:00.0: PCI post-resume error -19!
[  142.759248] xhci_hcd 0000:0b:00.0: HC died; cleaning up
[  142.759248] xhci_hcd 0000:09:00.0: PCI post-resume error -19!
[  142.759250] xhci_hcd 0000:09:00.0: HC died; cleaning up
[  142.759252] xhci_hcd 0000:0b:00.0: PM: dpm_run_callback(): pci_pm_resume+0x0/0xf0 returns -19
[  142.759256] xhci_hcd 0000:09:00.0: PM: dpm_run_callback(): pci_pm_resume+0x0/0xf0 returns -19
[  142.759260] xhci_hcd 0000:0b:00.0: PM: failed to resume async: error -19
[  142.759262] xhci_hcd 0000:09:00.0: PM: failed to resume async: error -19
[  142.805039] nvme nvme0: Shutdown timeout set to 8 seconds
[  142.819388] nvme nvme0: 8/0/0 default/read/poll queues
[  143.022481] usb 2-3: reset SuperSpeed USB device number 2 using xhci_hcd
[  143.165026] usb 1-7: reset full-speed USB device number 3 using xhci_hcd
[  143.431642] usb 1-8: reset high-speed USB device number 4 using xhci_hcd
[  143.644880] i915 0000:00:02.0: [drm] [ENCODER:94:DDI A/PHY A] is disabled/in DSI mode with an ungated DDI clock, gate it
[  143.644886] i915 0000:00:02.0: [drm] [ENCODER:102:DDI B/PHY B] is disabled/in DSI mode with an ungated DDI clock, gate it
[  143.644891] i915 0000:00:02.0: [drm] [ENCODER:118:DDI C/PHY C] is disabled/in DSI mode with an ungated DDI clock, gate it
[  146.149517] OOM killer enabled.
[  146.149518] Restarting tasks ...
[  146.149543] usb 3-1: USB disconnect, device number 2
[  146.149681] xhci_hcd 0000:0b:00.0: remove, state 4
[  146.149685] usb usb6: USB disconnect, device number 1
[  146.149688] r8152-cfgselector 6-1: USB disconnect, device number 2
[  146.152013] done.
[  146.152033] random: crng reseeded on system resumption
[  146.156228] thermal thermal_zone6: failed to read out thermal zone (-61)
[  146.159212] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_component_ops [i915])
[  146.218408] PM: suspend exit
[  146.258688] xhci_hcd 0000:0b:00.0: USB bus 6 deregistered
[  146.258697] xhci_hcd 0000:0b:00.0: remove, state 4
[  146.258700] usb usb5: USB disconnect, device number 1
[  146.258880] xhci_hcd 0000:0b:00.0: Host halt failed, -19
[  146.258883] xhci_hcd 0000:0b:00.0: Host not accessible, reset failed.
[  146.259049] xhci_hcd 0000:0b:00.0: USB bus 5 deregistered
[  146.259422] xhci_hcd 0000:09:00.0: remove, state 4
[  146.259425] usb usb4: USB disconnect, device number 1

dmesg nach 2. suspend, wo es dann geht:

  178.349324] ACPI: PM: Low-level resume complete
[  178.349369] ACPI: EC: EC started
[  178.349370] ACPI: PM: Restoring platform NVS memory
[  178.350431] Enabling non-boot CPUs ...
[  178.350550] x86: Booting SMP configuration:
[  178.350551] smpboot: Booting Node 0 Processor 1 APIC 0x2
[  178.352397] CPU1 is up
[  178.352494] smpboot: Booting Node 0 Processor 2 APIC 0x4
[  178.354351] CPU2 is up
[  178.354449] smpboot: Booting Node 0 Processor 3 APIC 0x6
[  178.356332] CPU3 is up
[  178.356450] smpboot: Booting Node 0 Processor 4 APIC 0x1
[  178.357275] CPU4 is up
[  178.357395] smpboot: Booting Node 0 Processor 5 APIC 0x3
[  178.358171] CPU5 is up
[  178.358292] smpboot: Booting Node 0 Processor 6 APIC 0x5
[  178.359132] CPU6 is up
[  178.359237] smpboot: Booting Node 0 Processor 7 APIC 0x7
[  178.360078] CPU7 is up
[  178.362786] ACPI: PM: Waking up from system sleep state S3
[  178.782408] ACPI: EC: interrupt unblocked
[  178.782521] pcieport 0000:00:1c.6: Intel SPT PCH root port ACS workaround enabled
[  178.782563] pcieport 0000:00:1d.0: Intel SPT PCH root port ACS workaround enabled
[  178.782612] pcieport 0000:00:1d.2: Intel SPT PCH root port ACS workaround enabled
[  178.900336] pcieport 0000:00:1c.0: Intel SPT PCH root port ACS workaround enabled
[  179.032594] vfio-pci 0000:01:00.0: Enabling HDA controller
[  179.034251] ACPI: EC: event unblocked
[  179.044888] nvme nvme0: Shutdown timeout set to 8 seconds
[  179.148443] nvme nvme0: 8/0/0 default/read/poll queues
[  179.323709] usb 2-3: reset SuperSpeed USB device number 2 using xhci_hcd
[  179.420457] i915 0000:00:02.0: [drm] [ENCODER:94:DDI A/PHY A] is disabled/in DSI mode with an ungated DDI clock, gate it
[  179.420464] i915 0000:00:02.0: [drm] [ENCODER:102:DDI B/PHY B] is disabled/in DSI mode with an ungated DDI clock, gate it
[  179.420470] i915 0000:00:02.0: [drm] [ENCODER:118:DDI C/PHY C] is disabled/in DSI mode with an ungated DDI clock, gate it
[  179.465669] usb 1-7: reset full-speed USB device number 3 using xhci_hcd
[  179.732246] usb 1-8: reset high-speed USB device number 4 using xhci_hcd
[  182.753337] OOM killer enabled.
[  182.753339] Restarting tasks ...
[  182.753373] usb 1-1: USB disconnect, device number 2
[  182.753482] pci 0000:07:00.0: [8086:15d3] type 01 class 0x060400
[  182.753595] pci 0000:07:00.0: enabling Extended Tags
[  182.753805] pci 0000:07:00.0: supports D1 D2
[  182.753807] pci 0000:07:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[  182.754065] pci 0000:07:00.0: 8.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x4 link at 0000:05:01.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
[  182.754276] pci 0000:07:00.0: Adding to iommu group 15
[  182.754319] pcieport 0000:05:01.0: ASPM: current common clock configuration is inconsistent, reconfiguring
[  182.755082] done.
[  182.755093] random: crng reseeded on system resumption
[  182.755957] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_component_ops [i915])
[  182.757974] thermal thermal_zone6: failed to read out thermal zone (-61)
[  182.762260] pci 0000:08:00.0: [8086:15d3] type 01 class 0x060400
[  182.762421] pci 0000:08:00.0: enabling Extended Tags
[  182.762723] pci 0000:08:00.0: supports D1 D2
[  182.762725] pci 0000:08:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[  182.763143] pci 0000:08:00.0: Adding to iommu group 15
[  182.763264] pci 0000:08:01.0: [8086:15d3] type 01 class 0x060400
[  182.763418] pci 0000:08:01.0: enabling Extended Tags
[  182.763702] pci 0000:08:01.0: supports D1 D2
[  182.763703] pci 0000:08:01.0: PME# supported from D0 D1 D2 D3hot D3cold
[  182.764111] pci 0000:08:01.0: Adding to iommu group 15
[  182.764240] pci 0000:08:02.0: [8086:15d3] type 01 class 0x060400
[  182.764390] pci 0000:08:02.0: enabling Extended Tags
[  182.764741] pci 0000:08:02.0: supports D1 D2
[  182.764743] pci 0000:08:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[  182.765146] pci 0000:08:02.0: Adding to iommu group 15
[  182.765270] pci 0000:08:03.0: [8086:15d3] type 01 class 0x060400
[  182.765421] pci 0000:08:03.0: enabling Extended Tags
[  182.765777] pci 0000:08:03.0: supports D1 D2
[  182.765779] pci 0000:08:03.0: PME# supported from D0 D1 D2 D3hot D3cold
[  182.766242] pci 0000:08:03.0: Adding to iommu group 15
[  182.766359] pci 0000:08:04.0: [8086:15d3] type 01 class 0x060400
[  182.766513] pci 0000:08:04.0: enabling Extended Tags
[  182.766810] pci 0000:08:04.0: supports D1 D2
[  182.766812] pci 0000:08:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[  182.767230] pci 0000:08:04.0: Adding to iommu group 15
[  182.767379] pci 0000:07:00.0: PCI bridge to [bus 08-3b]
[  182.767399] pci 0000:07:00.0:   bridge window [mem 0xc4000000-0xd9efffff]
[  182.767413] pci 0000:07:00.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[  182.767580] pci 0000:09:00.0: [1b73:1100] type 00 class 0x0c0330
[  182.767645] pci 0000:09:00.0: reg 0x10: [mem 0xc4000000-0xc400ffff 64bit]
[  182.767700] pci 0000:09:00.0: reg 0x18: [mem 0xc4010000-0xc4010fff 64bit]
[  182.767763] pci 0000:09:00.0: reg 0x20: [mem 0xc4011000-0xc4011fff 64bit]
[  182.768035] pci 0000:09:00.0: supports D1
[  182.768037] pci 0000:09:00.0: PME# supported from D0 D1 D3hot D3cold
[  182.768223] pci 0000:09:00.0: Adding to iommu group 15
[  182.775578] pci 0000:08:00.0: PCI bridge to [bus 09]
[  182.775599] pci 0000:08:00.0:   bridge window [mem 0xc4000000-0xc40fffff]
[  182.775723] pci 0000:08:01.0: PCI bridge to [bus 0a]
[  182.775879] pci 0000:0b:00.0: [1b73:1100] type 00 class 0x0c0330
[  182.775937] pci 0000:0b:00.0: reg 0x10: [mem 0xc4100000-0xc410ffff 64bit]
[  182.775976] pci 0000:0b:00.0: reg 0x18: [mem 0xc4110000-0xc4110fff 64bit]
[  182.776014] pci 0000:0b:00.0: reg 0x20: [mem 0xc4111000-0xc4111fff 64bit]
[  182.776219] pci 0000:0b:00.0: supports D1
[  182.776221] pci 0000:0b:00.0: PME# supported from D0 D1 D3hot D3cold
[  182.793085] pci 0000:0b:00.0: Adding to iommu group 15
[  182.803537] pci 0000:08:02.0: PCI bridge to [bus 0b]
[  182.803569] pci 0000:08:02.0:   bridge window [mem 0xc4100000-0xc41fffff]
[  182.806404] PM: suspend exit
[  182.809786] pci 0000:08:03.0: PCI bridge to [bus 0c]
[  182.813736] pci 0000:08:04.0: PCI bridge to [bus 0d-3b]
[  182.813757] pci 0000:08:04.0:   bridge window [mem 0xc4200000-0xd9efffff]
[  182.813769] pci 0000:08:04.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[  182.813866] pci_bus 0000:05: Allocating resources
[  182.813926] pci 0000:08:04.0: bridge window [io  0x1000-0x0fff] to [bus 0d-3b] add_size 1000
[  182.813930] pci 0000:07:00.0: bridge window [io  0x1000-0x0fff] to [bus 08-3b] add_size 1000
[  182.813936] pci 0000:07:00.0: BAR 13: assigned [io  0x2000-0x2fff]
[  182.813939] pci 0000:08:04.0: BAR 13: assigned [io  0x2000-0x2fff]
[  182.813941] pci 0000:08:00.0: PCI bridge to [bus 09]
[  182.813951] pci 0000:08:00.0:   bridge window [mem 0xc4000000-0xc40fffff]
[  182.813967] pci 0000:08:01.0: PCI bridge to [bus 0a]
[  182.813990] pci 0000:08:02.0: PCI bridge to [bus 0b]
[  182.813999] pci 0000:08:02.0:   bridge window [mem 0xc4100000-0xc41fffff]
[  182.814015] pci 0000:08:03.0: PCI bridge to [bus 0c]
[  182.814038] pci 0000:08:04.0: PCI bridge to [bus 0d-3b]
[  182.814042] pci 0000:08:04.0:   bridge window [io  0x2000-0x2fff]
[  182.814051] pci 0000:08:04.0:   bridge window [mem 0xc4200000-0xd9efffff]
[  182.814057] pci 0000:08:04.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[  182.814069] pci 0000:07:00.0: PCI bridge to [bus 08-3b]
[  182.814073] pci 0000:07:00.0:   bridge window [io  0x2000-0x2fff]
[  182.814081] pci 0000:07:00.0:   bridge window [mem 0xc4000000-0xd9efffff]
[  182.814088] pci 0000:07:00.0:   bridge window [mem 0xa0000000-0xc1ffffff 64bit pref]
[  182.814297] pcieport 0000:07:00.0: enabling device (0006 -> 0007)
[  182.821075] pcieport 0000:08:04.0: enabling device (0006 -> 0007)
[  182.822026] xhci_hcd 0000:09:00.0: xHCI Host Controller
[  182.822033] xhci_hcd 0000:09:00.0: new USB bus registered, assigned bus number 3
[  182.823398] xhci_hcd 0000:09:00.0: hcc params 0x200071e9 hci version 0x100 quirks 0x0000000000000410
[  182.832086] xhci_hcd 0000:09:00.0: xHCI Host Controller
[  182.832092] xhci_hcd 0000:09:00.0: new USB bus registered, assigned bus number 4
[  182.832096] xhci_hcd 0000:09:00.0: Host supports USB 3.0 SuperSpeed
[  182.832146] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.03

Irgendwelche Tipps? Das ist leider ganz schön nervig & ich überlege, mir eine "normale" USB-C dock zu holen & einen meiner beiden Monitore direkt am Notebook anzuschließen - ich hätte gern 2x WQHD 60 Hz extern und der T480 kann ja noch kein DP1.4...

Dankeschön

Beitrag automatisch zusammengeführt: 28 Mai 2023

Nachtrag.
Boltctl / lspci "funktionierend":

 ~ % boltctl
 ● Lenovo ThinkPad Thunderbolt 3 Dock
   ├─ type:          peripheral
   ├─ name:          ThinkPad Thunderbolt 3 Dock
   ├─ vendor:        Lenovo
   ├─ uuid:          00516960-1e95-0801-ffff-ffffffffffff
   ├─ generation:    Thunderbolt 3
   ├─ status:        authorized
   │  ├─ domain:     c3030000-00a2-a088-200a-2327c6235925
   │  ├─ rx speed:   40 Gb/s = 2 lanes * 20 Gb/s
   │  ├─ tx speed:   40 Gb/s = 2 lanes * 20 Gb/s
   │  └─ authflags:  boot
   ├─ authorized:    So 28 Mai 2023 11:06:43 UTC
   ├─ connected:     So 28 Mai 2023 11:06:43 UTC
   └─ stored:        Mo 24 Apr 2023 15:56:21 UTC
      ├─ policy:     iommu
      └─ key:        no

~ % lspci
00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v6/7th Gen Core Processor Host Bridge/DRAM Registers (rev 08)
00:02.0 VGA compatible controller: Intel Corporation UHD Graphics 620 (rev 07)
00:04.0 Signal processing controller: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor Thermal Subsystem (rev 08)
00:08.0 System peripheral: Intel Corporation Xeon E3-1200 v5/v6 / E3-1500 v5 / 6th/7th/8th Gen Core Processor Gaussian Mixture Model
00:14.0 USB controller: Intel Corporation Sunrise Point-LP USB 3.0 xHCI Controller (rev 21)
00:14.2 Signal processing controller: Intel Corporation Sunrise Point-LP Thermal subsystem (rev 21)
00:16.0 Communication controller: Intel Corporation Sunrise Point-LP CSME HECI #1 (rev 21)
00:1c.0 PCI bridge: Intel Corporation Sunrise Point-LP PCI Express Root Port #1 (rev f1)
00:1c.6 PCI bridge: Intel Corporation Sunrise Point-LP PCI Express Root Port #7 (rev f1)
00:1d.0 PCI bridge: Intel Corporation Sunrise Point-LP PCI Express Root Port #9 (rev f1)
00:1d.2 PCI bridge: Intel Corporation Sunrise Point-LP PCI Express Root Port #11 (rev f1)
00:1f.0 ISA bridge: Intel Corporation Sunrise Point LPC Controller/eSPI Controller (rev 21)
00:1f.2 Memory controller: Intel Corporation Sunrise Point-LP PMC (rev 21)
00:1f.3 Audio device: Intel Corporation Sunrise Point-LP HD Audio (rev 21)
00:1f.4 SMBus: Intel Corporation Sunrise Point-LP SMBus (rev 21)
00:1f.6 Ethernet controller: Intel Corporation Ethernet Connection (4) I219-LM (rev 21)
01:00.0 3D controller: NVIDIA Corporation GP108M [GeForce MX150] (rev a1)
03:00.0 Network controller: Intel Corporation Wireless 8265 / 8275 (rev 78)
04:00.0 PCI bridge: Intel Corporation JHL6240 Thunderbolt 3 Bridge (Low Power) [Alpine Ridge LP 2016] (rev 01)
05:00.0 PCI bridge: Intel Corporation JHL6240 Thunderbolt 3 Bridge (Low Power) [Alpine Ridge LP 2016] (rev 01)
05:01.0 PCI bridge: Intel Corporation JHL6240 Thunderbolt 3 Bridge (Low Power) [Alpine Ridge LP 2016] (rev 01)
05:02.0 PCI bridge: Intel Corporation JHL6240 Thunderbolt 3 Bridge (Low Power) [Alpine Ridge LP 2016] (rev 01)
06:00.0 System peripheral: Intel Corporation JHL6240 Thunderbolt 3 NHI (Low Power) [Alpine Ridge LP 2016] (rev 01)
07:00.0 PCI bridge: Intel Corporation JHL6540 Thunderbolt 3 Bridge (C step) [Alpine Ridge 4C 2016] (rev 02)
08:00.0 PCI bridge: Intel Corporation JHL6540 Thunderbolt 3 Bridge (C step) [Alpine Ridge 4C 2016] (rev 02)
08:01.0 PCI bridge: Intel Corporation JHL6540 Thunderbolt 3 Bridge (C step) [Alpine Ridge 4C 2016] (rev 02)
08:02.0 PCI bridge: Intel Corporation JHL6540 Thunderbolt 3 Bridge (C step) [Alpine Ridge 4C 2016] (rev 02)
08:03.0 PCI bridge: Intel Corporation JHL6540 Thunderbolt 3 Bridge (C step) [Alpine Ridge 4C 2016] (rev 02)
08:04.0 PCI bridge: Intel Corporation JHL6540 Thunderbolt 3 Bridge (C step) [Alpine Ridge 4C 2016] (rev 02)
09:00.0 USB controller: Fresco Logic FL1100 USB 3.0 Host Controller (rev 10)
0b:00.0 USB controller: Fresco Logic FL1100 USB 3.0 Host Controller (rev 10)
3d:00.0 Non-Volatile memory controller: Samsung Electronics Co Ltd NVMe SSD Controller SM981/PM981/PM983

Im nicht funktionierenden Fall fehlen die USB Geräte am Dock und bei lspci folgende Einträge; der Rest ist identisch (auch boltctl)

07:00.0 PCI bridge: Intel Corporation JHL6540 Thunderbolt 3 Bridge (C step) [Alpine Ridge 4C 2016] (rev 02)
08:00.0 PCI bridge: Intel Corporation JHL6540 Thunderbolt 3 Bridge (C step) [Alpine Ridge 4C 2016] (rev 02)
08:01.0 PCI bridge: Intel Corporation JHL6540 Thunderbolt 3 Bridge (C step) [Alpine Ridge 4C 2016] (rev 02)
08:02.0 PCI bridge: Intel Corporation JHL6540 Thunderbolt 3 Bridge (C step) [Alpine Ridge 4C 2016] (rev 02)
08:03.0 PCI bridge: Intel Corporation JHL6540 Thunderbolt 3 Bridge (C step) [Alpine Ridge 4C 2016] (rev 02)
08:04.0 PCI bridge: Intel Corporation JHL6540 Thunderbolt 3 Bridge (C step) [Alpine Ridge 4C 2016] (rev 02)
09:00.0 USB controller: Fresco Logic FL1100 USB 3.0 Host Controller (rev 10)
0b:00.0 USB controller: Fresco Logic FL1100 USB 3.0 Host Controller (rev 10)

 

[kristatos]

Hi,
ich habe mir auch mal so eine zugelegt und die tut's bei mir ohne Probleme (X13 Gen2i mit Debian 12). Laut fwupd ist die Firmware auch aktuell, hab aber nicht nachgesehen, welche explizit installiert ist.

 

[Matze88]

Ich habe jetzt bei dem Deal von der Dynabook TB4 Dock zugeschlagen: Hier sind meine Probleme sofort in Luft aufgelöst. Einzig etwas gewöhnungsbedürftig: Der Power-Button schaltet die Dock selbst ein und aus, dachte am Anfang, hier ist was kaputt

 

[Ambrosius]

@Matze88 hast du immer noch das gleiche OS wie bei der Thunderbolt im Betrieb? Wenn ja, wie hoch ist dein Swap Space (Partition/File) im VGL zu deinem verbauten RAM?

 

[Matze88]

Ja, habe ich, also die TB3 dock durch die Dynabook getauscht im laufenden Betrieb -> Probleme weg

free -m
               total        used        free      shared  buff/cache   available
Mem:           31979       17796       13969         997        1638       14183
Swap:          33791        3458       30333

 

[Ambrosius]

Ok ich sehe, du hast den Swap = RAM + ~ 2GiB drauf bei mir schauts auch ähnlich aus, hab einfach 2 GiB draufgepackt.. ich nutze Swap so gut wie nie im laufenden Betrieb, hab es nur aus Gründen des Standbys partioniert, obwohl es bei mir auch die Swapfile getan hätte...Ergo folgere ich daraus, dass nicht der mangelnde Swap Space zu suspend problemen geführt hat, aber ich sehe das hast du selbst schon deduziert..