luxnote lapstore servion thinkspot
Ergebnis 1 bis 5 von 5

Thema: Probleme mit tlp und fan sensor

  1. #1

    Registriert seit
    03.02.2018
    Beiträge
    21
    Danke
    2
    Thanked 0 Times in 0 Posts

    Probleme mit tlp und fan sensor

    Hallo,

    wenn ich tlp bei einem i7 eingeschalten habe friert mir die USB Wacom ein.
    Hat vielleicht einer das Problem gelößt?

    Das 2. ist, das keine fan Umdrehungszahl erkannt wird bei sensors.

    Vielleicht kann mir da jemand helfen.

    Danke.

    gruss Ralf

  2. #2
    Ubuntuversteher Avatar von linrunner
    Registriert seit
    22.06.2007
    Beiträge
    12.506
    Danke
    15
    Thanked 316 Times in 251 Posts
    Hi,

    die Anfrage wäre im Linux-Unterforum besser aufgehoben.

    zu 1.: ohne die in der Dokumentation unter Support geforderte Ausgabe kann ich nur raten, also bitte:
    Code:
    sudo tlp-stat
    zu 2.: wurde hier schon oft für die L-Reihe berichtet, somit ist auch keine Lüftersteuerung möglich. Lösung nicht bekannt.
    Gruß, linrunner
    X1C6, T450s, X220 - Ubuntu 18.04 - TLP - Ubuntu Schnelleinstieg
    -- Fehler im Anwender sind schwer zu beheben, da es meist keine Updates gibt


  3. Grund
    Doppelpost aufgrund SPAM-O-MATIC

  4. Grund
    Doppelpost aufgrund SPAM-O-MATIC

  5. #3

    Registriert seit
    03.02.2018
    Beiträge
    21
    Danke
    2
    Thanked 0 Times in 0 Posts
    Themenstarter
    hier die tlp-stst Ausgabe:

    --- TLP 1.2.2 --------------------------------------------

    +++ Configured Settings: /etc/default/tlp
    TLP_ENABLE=1
    TLP_DEFAULT_MODE=AC
    TLP_PERSISTENT_DEFAULT=0
    DISK_IDLE_SECS_ON_AC=0
    DISK_IDLE_SECS_ON_BAT=2
    MAX_LOST_WORK_SECS_ON_AC=15
    MAX_LOST_WORK_SECS_ON_BAT=60
    CPU_SCALING_MIN_FREQ_ON_AC=800000
    CPU_SCALING_MAX_FREQ_ON_AC=3300000
    CPU_SCALING_MIN_FREQ_ON_BAT=800000
    CPU_SCALING_MAX_FREQ_ON_BAT=3300000
    CPU_HWP_ON_AC=balance_performance
    CPU_HWP_ON_BAT=balance_power
    CPU_MIN_PERF_ON_AC=0
    CPU_MAX_PERF_ON_AC=100
    CPU_MIN_PERF_ON_BAT=0
    CPU_MAX_PERF_ON_BAT=30
    SCHED_POWERSAVE_ON_AC=1
    SCHED_POWERSAVE_ON_BAT=1
    NMI_WATCHDOG=1
    ENERGY_PERF_POLICY_ON_AC=performance
    ENERGY_PERF_POLICY_ON_BAT=power
    DISK_DEVICES="nvme0n1 sda"
    DISK_APM_LEVEL_ON_AC="254 254"
    DISK_APM_LEVEL_ON_BAT="128 128"
    SATA_LINKPWR_ON_AC="med_power_with_dipm max_performance"
    SATA_LINKPWR_ON_BAT="med_power_with_dipm min_power"
    AHCI_RUNTIME_PM_TIMEOUT=15
    INTEL_GPU_MIN_FREQ_ON_AC=0
    INTEL_GPU_MIN_FREQ_ON_BAT=0
    INTEL_GPU_MAX_FREQ_ON_AC=0
    INTEL_GPU_MAX_FREQ_ON_BAT=0
    INTEL_GPU_BOOST_FREQ_ON_AC=0
    INTEL_GPU_BOOST_FREQ_ON_BAT=0
    WIFI_PWR_ON_AC=off
    WIFI_PWR_ON_BAT=on
    WOL_DISABLE=Y
    SOUND_POWER_SAVE_ON_AC=0
    SOUND_POWER_SAVE_ON_BAT=1
    SOUND_POWER_SAVE_CONTROLLER=Y
    BAY_POWEROFF_ON_AC=0
    BAY_POWEROFF_ON_BAT=0
    BAY_DEVICE="sr0"
    RUNTIME_PM_ON_AC=on
    RUNTIME_PM_ON_BAT=auto
    USB_AUTOSUSPEND=1
    USB_BLACKLIST_BTUSB=0
    USB_BLACKLIST_PHONE=0
    USB_BLACKLIST_PRINTER=1
    USB_BLACKLIST_WWAN=0
    RESTORE_DEVICE_STATE_ON_STARTUP=0
    NATACPI_ENABLE=1
    TPACPI_ENABLE=1
    TPSMAPI_ENABLE=1

    +++ System Info
    System = LENOVO ThinkPad L540 20AUS04X00
    BIOS = J4ET64WW(1.64)
    Release = Ubuntu 18.04.3 LTS
    Kernel = 5.4.0-050400rc6-generic #201911031940 SMP Mon Nov 4 00:43:05 UTC 2019 x86_64
    /proc/cmdline = BOOT_IMAGE=/@/boot/vmlinuz-5.4.0-050400rc6-generic root=UUID=9fcdb22a-2fe5-491a-b52e-7c184880915f ro rootflags=subvol=@
    Init system = systemd v237
    Boot mode = BIOS (CSM, Legacy)

    +++ TLP Status
    State = enabled
    RDW state = enabled
    Last run = 10:00:10, 3704 sec(s) ago
    Mode = AC
    Power source = AC

    +++ Processor
    CPU model = Intel(R) Core(TM) i5-4300M CPU @ 2.60GHz

    /sys/devices/system/cpu/cpu0/cpufreq/scaling_driver = intel_pstate
    /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor = performance
    /sys/devices/system/cpu/cpu0/cpufreq/scaling_available_governors = performance powersave
    /sys/devices/system/cpu/cpu0/cpufreq/scaling_min_freq = 800000 [kHz]
    /sys/devices/system/cpu/cpu0/cpufreq/scaling_max_freq = 3300000 [kHz]

    /sys/devices/system/cpu/cpu1/cpufreq/scaling_driver = intel_pstate
    /sys/devices/system/cpu/cpu1/cpufreq/scaling_governor = performance
    /sys/devices/system/cpu/cpu1/cpufreq/scaling_available_governors = performance powersave
    /sys/devices/system/cpu/cpu1/cpufreq/scaling_min_freq = 800000 [kHz]
    /sys/devices/system/cpu/cpu1/cpufreq/scaling_max_freq = 3300000 [kHz]

    /sys/devices/system/cpu/cpu2/cpufreq/scaling_driver = intel_pstate
    /sys/devices/system/cpu/cpu2/cpufreq/scaling_governor = performance
    /sys/devices/system/cpu/cpu2/cpufreq/scaling_available_governors = performance powersave
    /sys/devices/system/cpu/cpu2/cpufreq/scaling_min_freq = 800000 [kHz]
    /sys/devices/system/cpu/cpu2/cpufreq/scaling_max_freq = 3300000 [kHz]

    /sys/devices/system/cpu/cpu3/cpufreq/scaling_driver = intel_pstate
    /sys/devices/system/cpu/cpu3/cpufreq/scaling_governor = performance
    /sys/devices/system/cpu/cpu3/cpufreq/scaling_available_governors = performance powersave
    /sys/devices/system/cpu/cpu3/cpufreq/scaling_min_freq = 800000 [kHz]
    /sys/devices/system/cpu/cpu3/cpufreq/scaling_max_freq = 3300000 [kHz]

    /sys/devices/system/cpu/intel_pstate/min_perf_pct = 24 [%]
    /sys/devices/system/cpu/intel_pstate/max_perf_pct = 100 [%]
    /sys/devices/system/cpu/intel_pstate/no_turbo = 0
    /sys/devices/system/cpu/intel_pstate/turbo_pct = 27 [%]
    /sys/devices/system/cpu/intel_pstate/num_pstates = 26

    x86_energy_perf_policy: program for your kernel not installed.

    /sys/module/workqueue/parameters/power_efficient = Y
    /proc/sys/kernel/nmi_watchdog = 1

    +++ Undervolting
    PHC kernel not available.

    +++ Temperatures
    CPU temp = 57 [°C]
    /proc/acpi/ibm/fan = 0 [/min]

    +++ File System
    /proc/sys/vm/laptop_mode = 0
    /proc/sys/vm/dirty_writeback_centisecs = 1500
    /proc/sys/vm/dirty_expire_centisecs = 1500
    /proc/sys/vm/dirty_ratio = 20
    /proc/sys/vm/dirty_background_ratio = 10

    +++ Storage Devices
    Devices = nvme0n1 sda

    /dev/nvme0n1: not present.

    /dev/sda:
    Type = ATA
    Model = KINGSTON SV300S37A480G
    Firmware = 605ABBF2
    APM Level = 254
    Status = active/idle
    TRIM = supported
    Scheduler = [mq-deadline] none (multi queue)

    Runtime PM: control = on, autosuspend_delay_ms = -1

    SMART info:
    9 Power_On_Hours_and_Msec = 14794 [h]
    12 Power_Cycle_Count = 1548
    189 Airflow_Temperature_Cel = 36 [°C]
    194 Temperature_Celsius = 36 (Min/Max 12/57) [°C]

    +++ AHCI Link Power Management (ALPM)
    /sys/class/scsi_host/host0/link_power_management_policy = med_power_with_dipm
    /sys/class/scsi_host/host1/link_power_management_policy = med_power_with_dipm
    /sys/class/scsi_host/host2/link_power_management_policy = med_power_with_dipm
    /sys/class/scsi_host/host3/link_power_management_policy = med_power_with_dipm
    /sys/class/scsi_host/host4/link_power_management_policy = med_power_with_dipm
    /sys/class/scsi_host/host5/link_power_management_policy = med_power_with_dipm

    +++ AHCI Host Controller Runtime Power Management
    /sys/bus/pci/devices/0000:00:1f.2/ata1/power/control = on
    /sys/bus/pci/devices/0000:00:1f.2/ata2/power/control = on
    /sys/bus/pci/devices/0000:00:1f.2/ata3/power/control = on
    /sys/bus/pci/devices/0000:00:1f.2/ata4/power/control = on
    /sys/bus/pci/devices/0000:00:1f.2/ata5/power/control = on
    /sys/bus/pci/devices/0000:00:1f.2/ata6/power/control = on

    +++ Docks and Device Bays
    /sys/devices/platform/dock.0: ata_bay = drive present

    +++ Intel Graphics
    /sys/module/i915/parameters/enable_dc = -1 (use per-chip default)
    /sys/module/i915/parameters/enable_fbc = 0 (disabled)
    /sys/module/i915/parameters/enable_psr = -1 (use per-chip default)
    /sys/module/i915/parameters/modeset = -1 (use per-chip default)

    /sys/class/drm/card0/gt_min_freq_mhz = 200 [MHz]
    /sys/class/drm/card0/gt_max_freq_mhz = 1250 [MHz]
    /sys/class/drm/card0/gt_boost_freq_mhz = 1250 [MHz]
    /sys/kernel/debug/dri/0/i915_ring_freq_table: 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050 1100 1150 1200 1250 [MHz]

    +++ Wireless
    bluetooth = on
    wifi = on
    wwan = none (no device)

    hci0(btusb) : bluetooth, not connected
    wlp2s0(iwlwifi) : wifi, connected, power management = off

    +++ Audio
    /sys/module/snd_hda_intel/parameters/power_save = 0
    /sys/module/snd_hda_intel/parameters/power_save_controller = N

    +++ PCIe Active State Power Management
    /sys/module/pcie_aspm/parameters/policy = default (using bios preferences)

    +++ Runtime Power Management
    Device blacklist = (not configured)
    Driver blacklist = amdgpu mei_me nouveau nvidia pcieport radeon (default)

    /sys/bus/pci/devices/0000:00:00.0/power/control = on (0x060000, Host bridge, no driver)
    /sys/bus/pci/devices/0000:00:02.0/power/control = on (0x030000, VGA compatible controller, i915)
    /sys/bus/pci/devices/0000:00:03.0/power/control = on (0x040300, Audio device, snd_hda_intel)
    /sys/bus/pci/devices/0000:00:14.0/power/control = on (0x0c0330, USB controller, xhci_hcd)
    /sys/bus/pci/devices/0000:00:16.0/power/control = on (0x078000, Communication controller, mei_me)
    /sys/bus/pci/devices/0000:00:19.0/power/control = on (0x020000, Ethernet controller, e1000e)
    /sys/bus/pci/devices/0000:00:1a.0/power/control = on (0x0c0320, USB controller, ehci-pci)
    /sys/bus/pci/devices/0000:00:1b.0/power/control = on (0x040300, Audio device, snd_hda_intel)
    /sys/bus/pci/devices/0000:00:1c.0/power/control = on (0x060400, PCI bridge, pcieport)
    /sys/bus/pci/devices/0000:00:1c.1/power/control = on (0x060400, PCI bridge, pcieport)
    /sys/bus/pci/devices/0000:00:1c.2/power/control = on (0x060400, PCI bridge, pcieport)
    /sys/bus/pci/devices/0000:00:1c.4/power/control = on (0x060400, PCI bridge, pcieport)
    /sys/bus/pci/devices/0000:00:1d.0/power/control = on (0x0c0320, USB controller, ehci-pci)
    /sys/bus/pci/devices/0000:00:1f.0/power/control = on (0x060100, ISA bridge, lpc_ich)
    /sys/bus/pci/devices/0000:00:1f.2/power/control = on (0x010601, SATA controller, ahci)
    /sys/bus/pci/devices/0000:00:1f.3/power/control = on (0x0c0500, SMBus, no driver)
    /sys/bus/pci/devices/0000:02:00.0/power/control = on (0x028000, Network controller, iwlwifi)
    /sys/bus/pci/devices/0000:08:00.0/power/control = on (0xff0000, Unassigned class [ff00], rtsx_pci)

    +++ USB
    Autosuspend = enabled
    Device whitelist = (not configured)
    Device blacklist = (not configured)
    Bluetooth blacklist = disabled
    Phone blacklist = disabled
    WWAN blacklist = disabled

    Bus 002 Device 002 ID 8087:8000 control = auto, autosuspend_delay_ms = 0 -- Intel Corp. (hub)
    Bus 002 Device 001 ID 1d6b:0002 control = auto, autosuspend_delay_ms = 0 -- Linux Foundation 2.0 root hub (hub)
    Bus 001 Device 002 ID 8087:8008 control = auto, autosuspend_delay_ms = 0 -- Intel Corp. (hub)
    Bus 001 Device 001 ID 1d6b:0002 control = auto, autosuspend_delay_ms = 0 -- Linux Foundation 2.0 root hub (hub)
    Bus 004 Device 001 ID 1d6b:0003 control = auto, autosuspend_delay_ms = 0 -- Linux Foundation 3.0 root hub (hub)
    Bus 003 Device 004 ID 24ae:2010 control = on, autosuspend_delay_ms = 2000 -- <unknown> (usbhid)
    Bus 003 Device 003 ID 058f:9540 control = auto, autosuspend_delay_ms = 2000 -- Alcor Micro Corp. AU9540 Smartcard Reader (no driver)
    Bus 003 Device 002 ID 056a:0065 control = on, autosuspend_delay_ms = 2000 -- Wacom Co., Ltd Bamboo (usbhid)
    Bus 003 Device 006 ID 04f2:b398 control = auto, autosuspend_delay_ms = 2000 -- Chicony Electronics Co., Ltd (uvcvideo)
    Bus 003 Device 005 ID 8087:07dc control = auto, autosuspend_delay_ms = 2000 -- Intel Corp. (btusb)
    Bus 003 Device 001 ID 1d6b:0002 control = auto, autosuspend_delay_ms = 0 -- Linux Foundation 2.0 root hub (hub)

    +++ Battery Features: Charge Thresholds and Recalibrate
    natacpi = active (data, thresholds)
    tpacpi-bat = inactive (kernel module 'acpi_call' not installed)
    tp-smapi = inactive (ThinkPad not supported)

    +++ ThinkPad Battery Status: BAT0 (Main / Internal)
    /sys/class/power_supply/BAT0/manufacturer = SANYO
    /sys/class/power_supply/BAT0/model_name = 45N1769
    /sys/class/power_supply/BAT0/cycle_count = (not supported)
    /sys/class/power_supply/BAT0/energy_full_design = 56160 [mWh]
    /sys/class/power_supply/BAT0/energy_full = 48830 [mWh]
    /sys/class/power_supply/BAT0/energy_now = 48820 [mWh]
    /sys/class/power_supply/BAT0/power_now = 0 [mW]
    /sys/class/power_supply/BAT0/status = Unknown (threshold effective)

    /sys/class/power_supply/BAT0/charge_start_threshold = 96 [%]
    /sys/class/power_supply/BAT0/charge_stop_threshold = 100 [%]

    Charge = 100.0 [%]
    Capacity = 86.9 [%]

    +++ Recommendations
    * Install acpi_call kernel module for ThinkPad battery recalibration

  6. #4
    Ubuntuversteher Avatar von linrunner
    Registriert seit
    22.06.2007
    Beiträge
    12.506
    Danke
    15
    Thanked 316 Times in 251 Posts
    Zitat Zitat von rrbs Beitrag anzeigen
    Bus 003 Device 002 ID 056a:0065 control = on, autosuspend_delay_ms = 2000 -- Wacom Co., Ltd Bamboo (usbhid)
    USB Autosuspend ist für das Gerät aus ("on" bedeutet hier "Gerät immer an"), das macht TLP für alle Eingabegeräte automatisch.

    Wo tritt denn das Problem auf: im Akku- oder im Netzbetrieb? Letzteres hast Du gepostet, aber ich vermute, es passiert am Akku. Dann bitte künftig auch die passende Ausgabe zeigen.

    Ich habe eine Anleitung zur Fehlereingrenzung geschrieben. In deinem Fall würde ich mal mit Step 6.1 PCIe weitermachen.

    Zuvor sollten wir aber ganz sicher sein, dass TLP wirklich die Ursache ist. Dazu müsstest Du Step 3 ausführen.
    Geändert von linrunner (07.11.2019 um 19:51 Uhr)
    Gruß, linrunner
    X1C6, T450s, X220 - Ubuntu 18.04 - TLP - Ubuntu Schnelleinstieg
    -- Fehler im Anwender sind schwer zu beheben, da es meist keine Updates gibt


  7. #5

    Registriert seit
    03.02.2018
    Beiträge
    21
    Danke
    2
    Thanked 0 Times in 0 Posts
    Themenstarter
    So ich habe das gemacht was Du sagtest und habe pci und usb bearbeitet.
    Jetzt scheint Alles wieder zu funktionieren.

    Danke für die Tips.

    schönes WE

    PS: Hast Du noch Tips für das L540?
    Gibt es da einen besseren Lüfter oder so?
    Geändert von rrbs (08.11.2019 um 17:41 Uhr)

Ähnliche Themen

  1. Antworten: 9
    Letzter Beitrag: 08.01.2014, 18:09
  2. Antworten: 10
    Letzter Beitrag: 30.01.2013, 21:28
  3. TLP - Probleme mit der Installation
    Von macjoshua im Forum Linux
    Antworten: 13
    Letzter Beitrag: 30.01.2013, 20:35
  4. [ERLEDIGT] T420 TLP und Lüfter Probleme
    Von hscade im Forum Linux
    Antworten: 9
    Letzter Beitrag: 09.12.2011, 18:46
  5. Probleme mit dem Fingerprint-Sensor
    Von toco im Forum X - Serie (inkl. Tablet)
    Antworten: 4
    Letzter Beitrag: 24.08.2006, 03:13

Lesezeichen

Berechtigungen

  • Neue Themen erstellen: Nein
  • Themen beantworten: Nein
  • Anhänge hochladen: Nein
  • Beiträge bearbeiten: Nein
  •  
ipWeb ok1.de Campus Preiswerte-IT - Gebrauchte Lenovo Notebooks kaufen CaptainNotebook NBWN - Notebooks wie neu