luxnote lapstore servion thinkspot
Seite 2 von 2 ErsteErste 12
Ergebnis 21 bis 24 von 24

Thema: [beendet] TLP 1.2 Beta-Test

  1. #21

    Registriert seit
    18.03.2009
    Beiträge
    1.140
    Danke
    36
    Thanked 71 Times in 68 Posts
    Zitat Zitat von linrunner Beitrag anzeigen
    @all: 1.1.908 ist hochgeladen.


    Nicht einfach wiederholen bitte und niemals ohne Ausgaben und/oder genauer Beschreibung des Hergangs.

    Bei Fehlern stets zuerst die Terminal-Ein- und Ausgaben (tlp setcharge?) wegkopieren und posten.

    Außerdem bei Akkuthemen immer:
    Code:
    sudo tlp-stat -b


    ok ok also installiere ich erstmal die neue version & setze dann die Schwellen erneut ?!? Wenn es dann funktioniert ist es soweit i.o. ?

    - - - Beitrag zusammengeführt - - -

    Unter 1.1.908 leider das gleiche:

    tlp setzt für beide Batterien den Startwert von bat1

    Code:
    sudo tlp start
    Code:
    sudo tlp-stat -b
    --- TLP 1.1.908 --------------------------------------------
    
    +++ Battery Features
    natacpi    = inactive (no kernel support)
    tpacpi-bat = active (thresholds, discharge)
    tp-smapi   = inactive (ThinkPad not supported)
    
    +++ ThinkPad Battery Status: BAT0 (Main / Internal)
    /sys/class/power_supply/BAT0/manufacturer                   = SANYO
    /sys/class/power_supply/BAT0/model_name                     = 45N1773
    /sys/class/power_supply/BAT0/cycle_count                    = (not supported)
    /sys/class/power_supply/BAT0/energy_full_design             =  23200 [mWh]
    /sys/class/power_supply/BAT0/energy_full                    =  17850 [mWh]
    /sys/class/power_supply/BAT0/energy_now                     =  15710 [mWh]
    /sys/class/power_supply/BAT0/power_now                      =      0 [mW]
    /sys/class/power_supply/BAT0/status                         = Unknown (threshold effective)
    
    tpacpi-bat.BAT0.startThreshold                              =     42 [%]
    tpacpi-bat.BAT0.stopThreshold                               =    100 [%]
    tpacpi-bat.BAT0.forceDischarge                              =      0
    
    Charge                                                      =   88.0 [%]
    Capacity                                                    =   76.9 [%]
    
    +++ ThinkPad Battery Status: BAT1 (Ultrabay / Slice / Replaceable)
    /sys/class/power_supply/BAT1/manufacturer                   = SANYO
    /sys/class/power_supply/BAT1/model_name                     = 45N1775
    /sys/class/power_supply/BAT1/cycle_count                    = (not supported)
    /sys/class/power_supply/BAT1/energy_full_design             =  23200 [mWh]
    /sys/class/power_supply/BAT1/energy_full                    =  17600 [mWh]
    /sys/class/power_supply/BAT1/energy_now                     =  17600 [mWh]
    /sys/class/power_supply/BAT1/power_now                      =      0 [mW]
    /sys/class/power_supply/BAT1/status                         = Full
    
    tpacpi-bat.BAT1.startThreshold                              =     42 [%]
    tpacpi-bat.BAT1.stopThreshold                               =    100 [%]
    tpacpi-bat.BAT1.forceDischarge                              =      0
    
    Charge                                                      =  100.0 [%]
    Capacity                                                    =   75.9 [%]
    
    +++ Charge total                                            =   94.0 [%]
    Code:
    # ------------------------------------------------------------------------------
    # tlp - Parameters for power saving
    # See full explanation: http://linrunner.de/en/tlp/docs/tlp-configuration.html
    
    # Hint: some features are disabled by default, remove the leading # to enable
    # them.
    
    # Set to 0 to disable, 1 to enable TLP.
    TLP_ENABLE=1
    
    # Operation mode when no power supply can be detected: AC, BAT.
    # Concerns some desktop and embedded hardware only.
    TLP_DEFAULT_MODE=AC
    
    # Operation mode select: 0=depend on power source, 1=always use TLP_DEFAULT_MODE
    # Hint: use in conjunction with TLP_DEFAULT_MODE=BAT for BAT settings on AC.
    TLP_PERSISTENT_DEFAULT=0
    
    # Seconds laptop mode has to wait after the disk goes idle before doing a sync.
    # Non-zero value enables, zero disables laptop mode.
    DISK_IDLE_SECS_ON_AC=0
    DISK_IDLE_SECS_ON_BAT=2
    
    # Dirty page values (timeouts in secs).
    MAX_LOST_WORK_SECS_ON_AC=15
    MAX_LOST_WORK_SECS_ON_BAT=60
    
    # Hint: CPU parameters below are disabled by default, remove the leading #
    # to enable them, otherwise kernel default values are used.
    
    # Select a CPU frequency scaling governor.
    # Intel Core i processor with intel_pstate driver:
    #   powersave(*), performance.
    # Older hardware with acpi-cpufreq driver:
    #   ondemand(*), powersave, performance, conservative, schedutil.
    # (*) is recommended.
    # Hint: use tlp-stat -p to show the active driver and available governors.
    # Important:
    #   powersave for intel_pstate and ondemand for acpi-cpufreq are power
    #   efficient for *almost all* workloads and therefore kernel and most
    #   distributions have chosen them as defaults. If you still want to change,
    #   you should know what you're doing! You *must* disable your distribution's
    #   governor settings or conflicts will occur.
    #CPU_SCALING_GOVERNOR_ON_AC=powersave
    #CPU_SCALING_GOVERNOR_ON_BAT=powersave
    
    # Set the min/max frequency available for the scaling governor.
    # Possible values strongly depend on your CPU. For available frequencies see
    # the output of tlp-stat -p.
    #CPU_SCALING_MIN_FREQ_ON_AC=0
    #CPU_SCALING_MAX_FREQ_ON_AC=0
    #CPU_SCALING_MIN_FREQ_ON_BAT=0
    #CPU_SCALING_MAX_FREQ_ON_BAT=0
    
    # Set energy performance hints (HWP) for Intel P-state governor:
    #   performance, balance_performance, default, balance_power, power
    # Values are given in order of increasing power saving.
    # Note: Intel Skylake or newer CPU and Kernel >= 4.10 required.
    CPU_HWP_ON_AC=balance_performance
    CPU_HWP_ON_BAT=balance_power
    
    # Set Intel P-state performance: 0..100 (%).
    # Limit the max/min P-state to control the power dissipation of the CPU.
    # Values are stated as a percentage of the available performance.
    # Requires an Intel Core i processor with intel_pstate driver.
    #CPU_MIN_PERF_ON_AC=0
    #CPU_MAX_PERF_ON_AC=100
    #CPU_MIN_PERF_ON_BAT=0
    #CPU_MAX_PERF_ON_BAT=30
    
    # Set the CPU "turbo boost" feature: 0=disable, 1=allow
    # Requires an Intel Core i processor.
    # Important:
    # - This may conflict with your distribution's governor settings
    # - A value of 1 does *not* activate boosting, it just allows it
    #CPU_BOOST_ON_AC=1
    #CPU_BOOST_ON_BAT=0
    
    # Minimize number of used CPU cores/hyper-threads under light load conditions:
    #   0=disable, 1=enable.
    SCHED_POWERSAVE_ON_AC=0
    SCHED_POWERSAVE_ON_BAT=1
    
    # Kernel NMI Watchdog:
    #   0=disable (default, saves power), 1=enable (for kernel debugging only).
    NMI_WATCHDOG=0
    
    # Change CPU voltages aka "undervolting" - Kernel with PHC patch required.
    # Frequency voltage pairs are written to:
    #   /sys/devices/system/cpu/cpu0/cpufreq/phc_controls
    # CAUTION: only use this, if you thoroughly understand what you are doing!
    #PHC_CONTROLS="F:V F:V F:V F:V"
    
    # Set CPU performance versus energy savings policy:
    #   performance, balance-performance, default, balance-power, power.
    # Values are given in order of increasing power saving.
    # Requires kernel module msr and x86_energy_perf_policy from linux-tools.
    ENERGY_PERF_POLICY_ON_AC=performance
    ENERGY_PERF_POLICY_ON_BAT=power
    
    # Disk devices; separate multiple devices with spaces (default: sda).
    # Devices can be specified by disk ID also (lookup with: tlp diskid).
    DISK_DEVICES="sda sdb"
    
    # Disk advanced power management level: 1..254, 255 (max saving, min, off).
    # Levels 1..127 may spin down the disk; 255 allowable on most drives.
    # Separate values for multiple disks with spaces. Use the special value 'keep'
    # to keep the hardware default for the particular disk.
    DISK_APM_LEVEL_ON_AC="254 254"
    DISK_APM_LEVEL_ON_BAT="128 128"
    
    # Hard disk spin down timeout:
    #   0:        spin down disabled
    #   1..240:   timeouts from 5s to 20min (in units of 5s)
    #   241..251: timeouts from 30min to 5.5 hours (in units of 30min)
    # See 'man hdparm' for details.
    # Separate values for multiple disks with spaces. Use the special value 'keep'
    # to keep the hardware default for the particular disk.
    #DISK_SPINDOWN_TIMEOUT_ON_AC="0 0"
    #DISK_SPINDOWN_TIMEOUT_ON_BAT="0 0"
    
    # Select IO scheduler for the disk devices: cfq, deadline, noop (Default: cfq).
    # Separate values for multiple disks with spaces. Use the special value 'keep'
    # to keep the kernel default scheduler for the particular disk.
    #DISK_IOSCHED="cfq cfq"
    
    # AHCI link power management (ALPM) for disk devices:
    #   min_power, med_power_with_dipm(*), medium_power, max_performance.
    # (*) Kernel >= 4.15 required, then recommended.
    # Multiple values separated with spaces are tried sequentially until success.
    SATA_LINKPWR_ON_AC="med_power_with_dipm max_performance"
    SATA_LINKPWR_ON_BAT="med_power_with_dipm min_power"
    
    # Exclude host devices from AHCI link power management.
    # Separate multiple hosts with spaces.
    #SATA_LINKPWR_BLACKLIST="host1"
    
    # Runtime Power Management for AHCI host and disks devices:
    #   on=disable, auto=enable.
    # EXPERIMENTAL ** WARNING: auto will most likely cause system lockups/data loss.
    #AHCI_RUNTIME_PM_ON_AC=on
    #AHCI_RUNTIME_PM_ON_BAT=on
    
    # Seconds of inactivity before disk is suspended.
    AHCI_RUNTIME_PM_TIMEOUT=15
    
    # PCI Express Active State Power Management (PCIe ASPM):
    #   default, performance, powersave.
    PCIE_ASPM_ON_AC=performance
    PCIE_ASPM_ON_BAT=powersave
    
    # Radeon graphics clock speed (profile method): low, mid, high, auto, default;
    # auto = mid on BAT, high on AC; default = use hardware defaults.
    RADEON_POWER_PROFILE_ON_AC=high
    RADEON_POWER_PROFILE_ON_BAT=low
    
    # Radeon dynamic power management method (DPM): battery, performance.
    RADEON_DPM_STATE_ON_AC=performance
    RADEON_DPM_STATE_ON_BAT=battery
    
    # Radeon DPM performance level: auto, low, high; auto is recommended.
    RADEON_DPM_PERF_LEVEL_ON_AC=auto
    RADEON_DPM_PERF_LEVEL_ON_BAT=auto
    
    # WiFi power saving mode: on=enable, off=disable; not supported by all adapters.
    WIFI_PWR_ON_AC=off
    WIFI_PWR_ON_BAT=on
    
    # Disable wake on LAN: Y/N.
    WOL_DISABLE=Y
    
    # Enable audio power saving for Intel HDA, AC97 devices (timeout in secs).
    # A value of 0 disables, >=1 enables power saving (recommended: 1).
    SOUND_POWER_SAVE_ON_AC=0
    SOUND_POWER_SAVE_ON_BAT=0
    
    # Disable controller too (HDA only): Y/N.
    SOUND_POWER_SAVE_CONTROLLER=Y
    
    # Power off optical drive in UltraBay/MediaBay: 0=disable, 1=enable.
    # Drive can be powered on again by releasing (and reinserting) the eject lever
    # or by pressing the disc eject button on newer models.
    # Note: an UltraBay/MediaBay hard disk is never powered off.
    BAY_POWEROFF_ON_AC=0
    BAY_POWEROFF_ON_BAT=0
    # Optical drive device to power off (default sr0).
    BAY_DEVICE="sr0"
    
    # Runtime Power Management for PCI(e) bus devices: on=disable, auto=enable.
    RUNTIME_PM_ON_AC=on
    RUNTIME_PM_ON_BAT=auto
    
    # Exclude PCI(e) device adresses the following list from Runtime PM
    # (separate with spaces). Use lspci to get the adresses (1st column).
    #RUNTIME_PM_BLACKLIST="bb:dd.f 11:22.3 44:55.6"
    
    # Exclude PCI(e) devices assigned to the listed drivers from Runtime PM.
    # Default when unconfigured is "amdgpu nouveau nvidia radeon" which
    # prevents accidential power-on of dGPU in hybrid graphics setups.
    # Use "" to disable the feature completely.
    # Separate multiple drivers with spaces.
    #RUNTIME_PM_DRIVER_BLACKLIST="amdgpu nouveau nvidia radeon"
    
    # Set to 0 to disable, 1 to enable USB autosuspend feature.
    USB_AUTOSUSPEND=1
    
    # Exclude listed devices from USB autosuspend (separate with spaces).
    # Use lsusb to get the ids.
    # Note: input devices (usbhid) are excluded automatically
    #USB_BLACKLIST="1111:2222 3333:4444"
    
    # Bluetooth devices are excluded from USB autosuspend:
    #   0=do not exclude, 1=exclude.
    USB_BLACKLIST_BTUSB=0
    
    # Phone devices are excluded from USB autosuspend:
    #   0=do not exclude, 1=exclude (enable charging).
    USB_BLACKLIST_PHONE=0
    
    # Printers are excluded from USB autosuspend:
    #   0=do not exclude, 1=exclude.
    USB_BLACKLIST_PRINTER=1
    
    # WWAN devices are excluded from USB autosuspend:
    #   0=do not exclude, 1=exclude.
    USB_BLACKLIST_WWAN=1
    
    # Include listed devices into USB autosuspend even if already excluded
    # by the blacklists above (separate with spaces).
    # Use lsusb to get the ids.
    #USB_WHITELIST="1111:2222 3333:4444"
    
    # Set to 1 to disable autosuspend before shutdown, 0 to do nothing
    # (workaround for USB devices that cause shutdown problems).
    #USB_AUTOSUSPEND_DISABLE_ON_SHUTDOWN=1
    
    # Restore radio device state (Bluetooth, WiFi, WWAN) from previous shutdown
    # on system startup: 0=disable, 1=enable.
    # Hint: the parameters DEVICES_TO_DISABLE/ENABLE_ON_STARTUP/SHUTDOWN below
    #   are ignored when this is enabled!
    RESTORE_DEVICE_STATE_ON_STARTUP=0
    
    # Radio devices to disable on startup: bluetooth, wifi, wwan.
    # Separate multiple devices with spaces.
    #DEVICES_TO_DISABLE_ON_STARTUP="bluetooth wifi wwan"
    
    # Radio devices to enable on startup: bluetooth, wifi, wwan.
    # Separate multiple devices with spaces.
    #DEVICES_TO_ENABLE_ON_STARTUP="wifi"
    
    # Radio devices to disable on shutdown: bluetooth, wifi, wwan.
    # (workaround for devices that are blocking shutdown).
    #DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth wifi wwan"
    
    # Radio devices to enable on shutdown: bluetooth, wifi, wwan.
    # (to prevent other operating systems from missing radios).
    #DEVICES_TO_ENABLE_ON_SHUTDOWN="wwan"
    
    # Radio devices to enable on AC: bluetooth, wifi, wwan.
    #DEVICES_TO_ENABLE_ON_AC="bluetooth wifi wwan"
    
    # Radio devices to disable on battery: bluetooth, wifi, wwan.
    #DEVICES_TO_DISABLE_ON_BAT="bluetooth wifi wwan"
    
    # Radio devices to disable on battery when not in use (not connected):
    #   bluetooth, wifi, wwan.
    #DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth wifi wwan"
    
    # Battery charge thresholds (ThinkPad only, tp-smapi or acpi-call kernel module
    # required). Charging starts when the remaining capacity falls below the
    # START_CHARGE_THRESH value and stops when exceeding the STOP_CHARGE_THRESH value.
    # Main / Internal battery (values in %)
    START_CHARGE_THRESH_BAT0=55
    # STOP_CHARGE_THRESH_BAT0=60
    # Ultrabay / Slice / Replaceable battery (values in %)
    START_CHARGE_THRESH_BAT1=42
    # STOP_CHARGE_THRESH_BAT1=80
    
    # Restore charge thresholds when AC is unplugged: 0=disable, 1=enable.
    RESTORE_THRESHOLDS_ON_BAT=1
    
    # ------------------------------------------------------------------------------
    # tlp-rdw - Parameters for the radio device wizard
    # Possible devices: bluetooth, wifi, wwan.
    
    # Hints:
    # - Parameters are disabled by default, remove the leading # to enable them
    # - Separate multiple radio devices with spaces
    
    # Radio devices to disable on connect.
    DEVICES_TO_DISABLE_ON_LAN_CONNECT="wifi"
    #DEVICES_TO_DISABLE_ON_WIFI_CONNECT="wwan"
    #DEVICES_TO_DISABLE_ON_WWAN_CONNECT="wifi"
    
    # Radio devices to enable on disconnect.
    DEVICES_TO_ENABLE_ON_LAN_DISCONNECT="wifi"
    #DEVICES_TO_ENABLE_ON_WIFI_DISCONNECT=""
    #DEVICES_TO_ENABLE_ON_WWAN_DISCONNECT=""
    
    # Radio devices to enable/disable when docked.
    #DEVICES_TO_ENABLE_ON_DOCK=""
    #DEVICES_TO_DISABLE_ON_DOCK=""
    
    # Radio devices to enable/disable when undocked.
    #DEVICES_TO_ENABLE_ON_UNDOCK="wifi"
    #DEVICES_TO_DISABLE_ON_UNDOCK=""
    T440s - no camera, no microphone, Trackpad with 3 buttons, 2x SSDs, ChiMei/Innolux FHD
    Pop!_OS https://system76.com/pop

  2. #22
    Ubuntuversteher Avatar von linrunner
    Registriert seit
    22.06.2007
    Beiträge
    12.318
    Danke
    14
    Thanked 279 Times in 225 Posts
    Themenstarter
    @mcb: verflixt, ein Bug . Danke!

    - - - Beitrag zusammengeführt - - -

    Problem mit falschen Ladeschwellen für BAT0 gefixt in 1.1.909. Bitte nochmal testen.
    Gruß, linrunner
    X1C6, T450s, X220 - Ubuntu 18.04 - TLP - Ubuntu Schnelleinstieg
    -- Fehler im Anwender sind schwer zu beheben, da es meist keine Updates gibt


  3. #23

    Registriert seit
    18.03.2009
    Beiträge
    1.140
    Danke
    36
    Thanked 71 Times in 68 Posts
    Zitat Zitat von linrunner Beitrag anzeigen
    @mcb: verflixt, ein Bug . Danke!

    - - - Beitrag zusammengeführt - - -

    Problem mit falschen Ladeschwellen für BAT0 gefixt in 1.1.909. Bitte nochmal testen.
    Works ! Ich habe aber nur die untere Schwelle eingetragen.

    Code:
    sudo tlp-stat -b
    --- TLP 1.1.909 --------------------------------------------
    
    +++ Battery Features
    natacpi    = inactive (no kernel support)
    tpacpi-bat = active (thresholds, discharge)
    tp-smapi   = inactive (ThinkPad not supported)
    
    +++ ThinkPad Battery Status: BAT0 (Main / Internal)
    /sys/class/power_supply/BAT0/manufacturer                   = SANYO
    /sys/class/power_supply/BAT0/model_name                     = 45N1773
    /sys/class/power_supply/BAT0/cycle_count                    = (not supported)
    /sys/class/power_supply/BAT0/energy_full_design             =  23200 [mWh]
    /sys/class/power_supply/BAT0/energy_full                    =  17850 [mWh]
    /sys/class/power_supply/BAT0/energy_now                     =  15720 [mWh]
    /sys/class/power_supply/BAT0/power_now                      =      0 [mW]
    /sys/class/power_supply/BAT0/status                         = Unknown (threshold effective)
    
    tpacpi-bat.BAT0.startThreshold                              =     55 [%]
    tpacpi-bat.BAT0.stopThreshold                               =    100 [%]
    tpacpi-bat.BAT0.forceDischarge                              =      0
    
    Charge                                                      =   88.1 [%]
    Capacity                                                    =   76.9 [%]
    
    +++ ThinkPad Battery Status: BAT1 (Ultrabay / Slice / Replaceable)
    /sys/class/power_supply/BAT1/manufacturer                   = SANYO
    /sys/class/power_supply/BAT1/model_name                     = 45N1775
    /sys/class/power_supply/BAT1/cycle_count                    = (not supported)
    /sys/class/power_supply/BAT1/energy_full_design             =  23200 [mWh]
    /sys/class/power_supply/BAT1/energy_full                    =  17600 [mWh]
    /sys/class/power_supply/BAT1/energy_now                     =  15040 [mWh]
    /sys/class/power_supply/BAT1/power_now                      =      0 [mW]
    /sys/class/power_supply/BAT1/status                         = Unknown (threshold effective)
    
    tpacpi-bat.BAT1.startThreshold                              =     42 [%]
    tpacpi-bat.BAT1.stopThreshold                               =    100 [%]
    tpacpi-bat.BAT1.forceDischarge                              =      0
    
    Charge                                                      =   85.5 [%]
    Capacity                                                    =   75.9 [%]
    
    +++ Charge total                                            =   86.8 [%]
    Danke für den schnellen Bugfix !
    T440s - no camera, no microphone, Trackpad with 3 buttons, 2x SSDs, ChiMei/Innolux FHD
    Pop!_OS https://system76.com/pop

  4. #24
    Ubuntuversteher Avatar von linrunner
    Registriert seit
    22.06.2007
    Beiträge
    12.318
    Danke
    14
    Thanked 279 Times in 225 Posts
    Themenstarter
    Der Betatest ist beendet, denn das Release ist da: https://thinkpad-forum.de/threads/82...06#post2184006

    Herzlichen Dank allen Testern!
    Gruß, linrunner
    X1C6, T450s, X220 - Ubuntu 18.04 - TLP - Ubuntu Schnelleinstieg
    -- Fehler im Anwender sind schwer zu beheben, da es meist keine Updates gibt


Ähnliche Themen

  1. TLP 1.1 Beta-Test
    Von linrunner im Forum Linux
    Antworten: 23
    Letzter Beitrag: 18.01.2018, 08:00
  2. [Beendet] TLP 1.0 Beta-Test
    Von linrunner im Forum Linux
    Antworten: 42
    Letzter Beitrag: 31.05.2017, 23:12
  3. Antworten: 52
    Letzter Beitrag: 27.10.2011, 20:34
  4. Nigma-Utilities BETA Test
    Von consolinator im Forum Was sonst nicht passt
    Antworten: 59
    Letzter Beitrag: 05.11.2007, 08:20

Lesezeichen

Berechtigungen

  • Neue Themen erstellen: Nein
  • Themen beantworten: Nein
  • Anhänge hochladen: Nein
  • Beiträge bearbeiten: Nein
  •  
CeCon ok1.de ipWeb Campus Shop CaptainNotebook RO Electronic